nv publications N.V. Business Publications
43 Main Street
Avon By The Sea, NJ 07717
(732)502-0500
Fax: (732)502-9606
lprazych@nvpublications.com

N.V. Business Publications
540 W Frontage Rd. Suite 3124
Northfield, IL 60093-1230
(847)441-5645
Fax: (847)441-5652
advertising@nvpublications.com
Brunton Publications
1 Salisbury Office Park,
London Road
Salisbury, Wiltshire SP1 3HP
Tel: 011441722337038
publications@brunton.co.uk

NV PUBLICATIONS CLASSIFIEDS

Site Map

The Source 2014
Industry Calendar
(Click Below To View)

Get Adobe Flash player

INTERNET
DIRECTORIES
NV Publications BCN internet directorynv publications flexo internet directory


CLICK TO VIEW
The 2014
FMN Executive Outlook

EXPERT-BANNER2.jpg


wilkinson-pic.jpgWelcome to 'Ask The Expert'. This page is moderated by industry consultant, Steve Wilkinson.This page featuresthe answers to your questions.Our visitorscan also post comments to these questions/answers as well. You can learn more about Steve's background and our 'Ask The Expert' pageby Clicking Here.

If you have a new question to ask, just CLICK HERE to post your question. Questions and comments will be reviewed by our staff and posted as quickly as possible. All questions should be non-commercial in nature

As always, thanks for visiting www.nvpublications.com.


ASK-THE-EXPERT


July 19, 2010
We are about to switch from wiper rolls to a doctor bladed system, what are the pro's and cons between a bladed and two roll system?
   There is no doubt that if you want to achieve cleaner more consistent print quality then a doctor bladed system is the way to go.
    That said, if you have been running for a long time with a rubber wiper roll and your operators have little or no experience with using doctor blades then
you need to understand there will be a learning curve as with all new practices and equipment.
    You did not mention what type of doctor blade system you have adopted or what materials you will be using so I will briefly cover the basics of the available systems.
    When doctor blades were introduced, a positive angle (trailing blade) was used but today the reverse angle blade is used in most all flexo applications. Unlike the trailing blade the reverse angle blade works against the rotation of the anilox roll as it meters the excess ink from the surface of the anilox.
   Using a doctor blade will dramatically improve your control over the ink film thickness that you lay down and will allow you to run faster as, unlike your
old rubber wiper roll, the reverse angle blade will not be pushed away from the anilox surface as you try to run faster. This means however that you must maintain your anilox cleanliness and be more certain that you have the correct line count and volume engraving on your anilox as a blade will not allow you to open up the nip impression between, as you will have gotten used to with your wiper roll system.
    The blade angle and pressure are critical factors to maintaining a good clean wipe of your anilox surface. Blades can be made from a multitude of materials ranging from blue/white carbon steel, stainless steel, plastics, laminates, composites so there is a lot of choice, although carbon steel is by far the most common.
Blade thicknesses and blade tip configurations also vary, although the beveled tip blade is still the most common with thicknesses generally varying dependent
on the ink system being used, generally the more viscous the ink the thicker the blade.
    Inks need to be filtered in particular when using blades as any metal or hard particles that get into the ink can become trapped between the blade and anilox resulting in scoring of the anilox engraving. Blades must not be run out of alignment or dry as scoring of the anilox will also occur.
If you have selected a chamber blade system then you will have two blades, a metering blade and a retaining blade, so alignment, blade angle and pressure are even more critical.
    Seals also become a factor with chambered systems in retaining the ink in the chamber; make the wrong choice and you will have a lot of ink all over your press.
That said. the chamber system gives you the best control over your ink chemistry, its viscosity and will dramatically reduce your ink consumption as well as further improve the consistency of your print quality.
    Rubber wiper rolls have a tendency to wear unevenly, swell, shrink, crack and allow for excessive wiping pressure and exaggerated alignment issues so you have made the right choice whichever blade system you have chosen but you will have a learning curve and should ask for as much support from your vendor as you think you will or might need.

Add new comment

All fields are required.

*

*

*

No Comments




Archives

s

 

This Site  Created & Managed by Netincome LLC

NV PUBLICATIONS PACKAGING INDUSTRY

FLEXO MARKET NEWS  SEPTEMBER 22ND ISSUE NOW ONLINE
CLICK TO VIEW

SPONSORED BY